Just about everyone maintains their own unique perception in relation to Tools You Need to Install a New Bathtub .
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Mounting a bath tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is also a reasonably hard job. If the old tub is readily obtainable, the job can move speedily; if you need to open up a wall to remove the old bathtub as well as position the brand-new tub, the task is a lot harder. In either instance, the job is within a home handyman's abilities, although you will need an assistant to move out the old bathtub and embeded in the new one. Make sure you have actually qualified on your own for the task and fit attempting it. As opposed to employing a professional to take control of a halfway-completed job, it is better to think about employing one prior to you begin. Opportunities are you may require an expert plumber to make tube connections.
This post will aid you install a brand-new bathtub in your washroom if you have currently purchased a brand-new tub and also don't require to change the setup of your previous supply of water pipelines.
Your tools and also material list ought to consist of the following:
Removing Old Taps
If you need to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is disconnect the water. After doing so, turn on the faucets to drain pipes any water staying in the system. The procedure of removing the existing faucets can be fairly problematic because of the limited gain access to that is usually the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a fabric all set for the remaining water that will originate from the pipelines. As soon as the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been removed, the holes in the bath/basin will have to be cleaned of any old sealing compound.
Prior to moving on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will need a plastic connector to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, then you will call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the placing hole in the bath/basin guaranteeing that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the manufacturer given backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap connectors. The previous type needs to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Using both wood boards under its feet, place the bath tub in the needed position. The wood boards are practical in uniformly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the tub till the level reads degree.
To install faucets, fit the bottom of the outermost versatile faucet connector to the appropriate supply pipe by making a compression join; then do the very same for the other tap.
Activate the supply of water and also check all joints and brand-new pipework for leakages as well as tighten them if essential. Fill the tub as well as additionally check the overflow outlet and the typical electrical outlet for leaks.
Finally, take care of the bathroom paneling as defined in the producer's user's manual. Tiling and also securing around the bathtub ought to wait up until the tub has been utilized a minimum of when as this will certainly resolve it right into its last placement.
Planning for the Installment
To start with, the sustaining structure provided with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to see to it that if the faucet features a plastic washer, it is fitted between the bath and also the faucets. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to prevent pressure on the tub.
Fit the versatile tap connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to break a stiff seal, triggering the water to pass through the wall surface in between the bath and the tiling, resulting in complications with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your fixtures and also installations. They are sold in tubes and cartridges, and are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of soaked newspaper or soft rope. Remember to always fill the bathtub with water prior to securing, to permit the activity experienced when the bathtub remains in usage. The sealer can split relatively very early if you do not take into consideration this motion prior to sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently offered on the market. It is advisable to fit the tiles using waterproof or water-proof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent reader on Installing A Bathtub, I imagined sharing that chunk was essential. Are you aware of anybody else who is enthusiastic about the subject? Feel free to promote it. I take joy in reading our article about A Step-by-Step Guide to Installing a Bathtub.
Estimating